Emerald Masonry LLC
← All Posts

Foundation Masonry Repair · Chicagoland, IL

Adding an Egress Window to a Brick House or Block Foundation: What's Involved

Finishing a basement bedroom usually means adding an egress window, and on a Chicago-area brick home that means cutting into masonry. Here's what the codes generally require, how the opening is cut and supported, and the masonry details that keep it dry.

2026-11-14

Quick Answer

Adding an egress window to a brick house or block foundation means getting a permit, cutting a code-sized opening in the foundation and any brick above, supporting it with a properly sized lintel, rebuilding the edges, setting the window, and installing a drained window well. Emerald Masonry LLC, a family-owned Chicagoland contractor, gives free assessments: (708) 288-1696.

Adding an Egress Window to a Brick House or Block Foundation: What's Involved

Adding an Egress Window to a Brick House or Block Foundation

Adding an egress window to a brick house means cutting into masonry: a code-sized opening in the foundation and, often, in the brick above it, supported by a properly sized steel lintel, rebuilt cleanly at the edges, and finished with a window and a drained window well. Done right, it is safe, dry and looks like it was always there. Emerald Masonry LLC, a family-owned masonry contractor serving Chicago and the Chicagoland suburbs, does the masonry for these openings. Free on-site assessments: (708) 288-1696.

Finishing a basement is one of the most common projects on Chicago-area homes, and turning it into a bedroom almost always means adding an egress window: an opening large enough for someone to get out in an emergency and for firefighters to get in. On a frame house, that is mostly carpentry. On a brick bungalow, Georgian, raised ranch or two-flat, it is masonry and structural work. This guide explains what is involved.

An egress window is a hole in the part of the house that holds everything else up. Treat it like structural work, because it is.

What an egress window is, and why it is required

Building codes require every sleeping room, including a basement bedroom, to have an emergency escape and rescue opening. Most Illinois communities adopt the International Residential Code (IRC) with local changes. Under the IRC, the opening generally has to meet these minimums:

| Requirement | Typical IRC minimum | |---|---| | Net clear opening | 5.7 sq ft (5.0 sq ft for some grade-floor or below-grade openings) | | Clear opening height | 24 inches | | Clear opening width | 20 inches | | Sill height above floor | No more than 44 inches | | Window well area | At least 9 sq ft, with at least 36 inches of projection and width | | Ladder or steps | Required when the well is deeper than 44 inches |

These are general figures, and local codes and amendments vary. Always confirm the current requirements with your building department before designing the opening.

Most existing basement windows on older Chicago-area homes are much smaller than this, so meeting the code usually means enlarging an existing opening or cutting a new one.

Know your foundation and wall

How the opening is cut depends on what it is cut through.

Concrete block foundations

Common on many mid-century homes. Cutting block is straightforward, but the cut edges leave hollow cores that have to be filled and reinforced, and block walls carry the load in a way that makes the lintel essential.

Poured concrete foundations

Common on newer homes. Poured walls are typically cut with a large wet saw. They are strong, but often have reinforcement in them, and a clean, square cut is key to a good window fit.

Brick above grade

On many homes, especially raised ranches and bungalows, the basement window sits partly above grade, so the opening extends up into the brick. That brick has to be cut cleanly, a lintel set to carry it, and the brick rebuilt around the new window. On solid masonry walls that means every layer; on brick veneer it means the veneer plus the backup wall, with flashing and weep holes.

Older stone or brick foundations

On some older homes, the foundation itself is stone or brick laid in soft mortar. Openings in these walls need extra care and often an engineer's input.

Enlarge an existing window or cut a new opening?

Most homeowners start by asking whether the old basement window can simply be made bigger. Often it can, and it is usually the first option we look at.

Enlarging an existing opening

An existing window already has a lintel, a finished head and, on many homes, a well. Making it taller (by lowering the sill) is the simplest version, because the width and the lintel can sometimes stay. Making it wider almost always means a new, longer lintel, because the old one was sized for the smaller span. On older homes, the existing lintel is often rusted anyway and due for replacement.

Cutting a new opening

A new location makes sense when the existing windows are in the wrong room, sit under a deck or driveway, or are too close to a corner or a beam pocket to enlarge safely. It is more work: a full new lintel, new edges, and a new well, but it puts the window where the bedroom needs it.

| Factor | Enlarge existing | Cut new | |---|---|---| | Lintel | Often replaced with a longer one | Always new | | Room layout | Fixed to the old location | Choose the best location | | Outside space | Existing well may be reused or enlarged | New well and excavation | | Brick above grade | Rebuild at the widened edges | Cut and rebuild a full new opening |

Before any cutting: the planning checklist

  • Permit and plans: most municipalities require a permit, and some require an engineer's design for the opening and lintel.
  • Location: avoid gas, water, electrical and sewer lines, plus load points such as beams resting on the wall.
  • Grade and well: confirm there is room outside for a code-compliant well, especially on tight city lots and gangways.
  • Drainage: plan how the well will drain, usually to the drain tile or a gravel base, before the hole is dug.
  • Existing condition: walls that are already cracked, bowed or leaking should be assessed and addressed first.
  • Matching: plan the brick and mortar match for any above-grade rebuilding.

How an egress opening is cut and built

Every project differs, but a careful job generally follows this order.

  1. Lay out the opening to the required size, plus allowances for the window frame.
  2. Excavate outside down to the depth of the new well and below the sill.
  3. Support the wall above the opening where needed, with temporary shoring.
  4. Set the lintel: on brick and block walls, the lintel is often installed before or as the opening is cut, so the wall is carried the whole time.
  5. Cut the opening: block or brick is removed and edges cut square; poured concrete is sawn with a wet saw.
  6. Finish the edges: block cores are filled solid and reinforced as specified; brick is rebuilt and toothed in.
  7. Install the window in a properly sized buck or frame, sealed to the masonry.
  8. Flash and seal: install flashing at the head on above-grade brick, keep weep holes open, and seal the window perimeter.
  9. Build the well: set the well liner, a drain at the bottom tied into drainage, and a ladder or steps if required.
  10. Backfill and grade so surface water runs away from the well.
  11. Rebuild above-grade brick in matched brick and mortar and clean up.

Materials and techniques

| Item | What is typically used | Why it matters | |---|---|---| | Lintel | Steel angle or engineered lintel sized to the span and load | Carries the wall above the opening | | Block edges | Grout-filled cores, reinforcement as specified | Restores strength at the cut | | Brick rebuild | Matched face brick, toothed in | Keeps the wall bonded and blended | | Mortar | Type S below grade; Type N or matched mix above grade | Durability where wet; compatibility with existing brick | | Flashing | Flexible flashing over the head on brick walls | Sends water out, not in | | Window buck | Treated or composite frame sealed to masonry | Keeps the window and seal stable | | Well | Galvanized or composite liner, drain, gravel | Escape room and drainage |

See also lintel rust stains and orange streaks and Type N vs Type S mortar.

Common mistakes

  • No lintel, or one that is too small, leading to cracks above the opening.
  • Cutting before shoring on a loaded wall.
  • Hollow block edges left open, weakening the wall and letting water in.
  • Wells without drainage, which turn into basins and leak through the window.
  • Gray mortar and mismatched brick on the above-grade rebuild.
  • No flashing above the window on brick walls.
  • Opening too small to pass inspection once the window frame is in.

What drives the cost

  • Foundation type and wall thickness.
  • Enlarging an existing opening vs cutting new.
  • Brick work above grade, including matching.
  • Lintel size and any engineering.
  • Excavation and access, including tight side yards.
  • Window and well choices, including ladders and covers.
  • Drainage and backfill.
  • Permits and inspections.

Emerald Masonry LLC gives a written, itemized estimate for the masonry after a free on-site assessment.

DIY vs hiring a pro

Egress windows are a popular DIY topic online, but cutting a foundation is not a weekend project. The wall carries the house, the lintel has to be right, and a poor seal or undrained well becomes a leaking basement. Hire experienced trades for the structural and masonry work, and make sure the permit and inspections are in place.

Chicagoland context

Chicago-area basements were not built to be bedrooms. Bungalows from the 1910s to 1930s often have small, high basement windows in brick or block; post-war raised ranches and split-levels have larger windows partly above grade, with brick veneer above; and newer homes have poured foundations with small sliders. Clay-heavy soils hold water around foundations after heavy rains, so the well and its drainage matter as much as the opening. Narrow gangways on city lots can make wells tight. We see these projects in Chicago and suburbs such as Oak Lawn, Burbank, Evergreen Park, Orland Park and Downers Grove.

For related topics, see basement water: masonry or drainage?, when masonry needs a structural engineer and bricking up a window or door opening, the reverse of this job. For local foundation work, see our Mokena foundation masonry repair and Burbank foundation masonry repair pages.

Maintenance after installation

  • Keep the well drain clear of leaves and debris, especially in fall.
  • Use a well cover that lifts easily from inside, to keep out snow and leaves without blocking escape.
  • Check the window seal and the lintel each spring for gaps or rust.
  • Keep downspouts away from the well.
  • Watch the brick above the opening for new cracks in the first year.

Related services

Conclusion: right size, right support, right drainage

A good egress window meets the code, is carried by a properly sized lintel, has solid, sealed edges, and sits in a well that drains. Get the permit and any engineering in place first, plan the drainage before digging, and use masons who treat the foundation like the structural wall it is.

Emerald Masonry LLC is a family-owned masonry contractor serving Chicago and the Chicagoland suburbs, led by career masons with decades of hands-on Chicagoland experience, in foundation masonry repair, brick repair and replacement, tuckpointing and repointing, chimney repair, lintel and limestone sill repair, caulking, sealing, and residential, commercial and historic masonry restoration. Established 2024; licensed, bonded and insured. Free on-site assessments — call (708) 288-1696.

Planning a basement bedroom? Call (708) 288-1696 or book a free on-site assessment.

Frequently Asked Questions

Can you add an egress window to a brick house?

Yes. A code-sized opening is cut in the foundation and, where the window extends above grade, in the brick above it, then supported with a steel lintel, rebuilt at the edges and fitted with the window and a drained window well. It needs a permit and careful masonry work to stay dry and structurally sound.

What size does an egress window need to be?

Under the International Residential Code that most Illinois communities adopt, an egress opening generally needs at least 5.7 square feet of clear opening (5.0 for some grade-floor or below-grade openings), at least 24 inches of clear height and 20 inches of clear width, with the sill no more than 44 inches above the floor. Local amendments vary, so confirm with your building department.

Does cutting a new opening weaken my foundation?

It removes material, so it has to be done correctly: the opening is supported during cutting, sized properly, and spanned by a lintel or header that carries the load above. On block walls the edges are filled and reinforced. Some municipalities or situations require an engineer's design, especially for wide openings or walls that are already cracked.

Do I need a window well for an egress window?

Yes, when the window is below grade. Codes generally require a well with a minimum area and projection so a person can get out, and a ladder or steps when the well is deep. The well also needs drainage so it does not fill with water.

Is it better to enlarge an existing basement window or cut a new one?

Enlarging an existing window opening is often simpler, because there is already a lintel and an opening to work from, although the lintel usually has to be replaced to span the wider opening. A new location may be better for the room layout or to avoid utilities.

Do I need a permit for an egress window?

Almost always. Cutting a new opening in a foundation is structural work, and the egress window is usually part of a permitted basement finish. Check with your village or the City of Chicago before work.

How much does an egress window installation cost?

It depends on the foundation type, wall thickness, whether brick above has to be cut and rebuilt, lintel size, excavation and access, window and well choices, drainage, and permits. Emerald Masonry LLC gives a written, itemized estimate for the masonry after a free on-site look.

Who cuts egress window openings in brick and block near Chicago?

Emerald Masonry LLC, a family-owned masonry contractor based in Palos Heights, handles the masonry for egress openings on homes across Chicago and the Chicagoland suburbs, including the lintel, brick and block rebuilding and matching. Call (708) 288-1696 for a free on-site assessment.