Brick Repair · Chicagoland, IL
Bricking Up a Window, Door or AC Opening in a Brick House: How It's Done Right
Old through-wall air conditioner sleeves, unused doors, coal chutes and basement windows: Chicago-area brick homes are full of openings owners want to close. Here's how a mason bricks one up so it's solid, dry and hard to spot.
2026-11-07
Quick Answer
Bricking up a window, door or air conditioner opening in a brick house means removing the frame, toothing new brick into the existing courses, tying it to the wall, adding insulation and flashing where needed, and matching the brick and mortar so the infill blends. Emerald Masonry LLC, a family-owned Chicagoland contractor, gives free assessments: (708) 288-1696.

Bricking Up a Window, Door or AC Opening in a Brick House
Bricking up a window opening, an old door, or a through-wall air conditioner sleeve is a common job on Chicago-area brick homes. Done properly, the frame comes out, new brick is toothed into the existing courses, tied to the wall and matched in brick and mortar, and the inside is insulated and finished. The result is a solid, dry wall that is hard to pick out from the street. Emerald Masonry LLC, a family-owned masonry contractor serving Chicago and the Chicagoland suburbs, does this work. Free on-site assessments: (708) 288-1696.
Owners close openings for plenty of reasons: an AC sleeve replaced by central air, a side door no longer used after a remodel, a coal chute from a century ago, a basement window that leaks, or a kitchen layout that needs a solid wall. This guide covers how the work is done, the details that decide whether it blends in, and the rules to check first.
The difference between a patch and a proper infill is whether the new brick is woven into the old wall or just stacked inside a hole.
What kind of wall you have
Before planning the work, a mason needs to know how the wall is built, because the infill has to match it.
Solid masonry
Most older Chicago homes, including bungalows, two-flats and greystones, have solid masonry walls: two or more layers (wythes) of brick, with face brick outside and softer Chicago common brick behind. Bricks laid sideways across the layers tie them together. An infill on these walls fills every layer.
Brick veneer
Most homes built from the mid-century onward have brick veneer: one layer of brick over a wood or block backup wall, with an air space, masonry ties, flashing and weep holes. An infill here has to keep those details working.
| Feature | Solid masonry | Brick veneer | |---|---|---| | Typical homes | Pre-war bungalows, two-flats, greystones | Post-war ranches, raised ranches, newer homes | | Layers to fill | All wythes | Face brick plus backup wall | | Ties to existing | Toothed and bonded across wythes | Toothed face plus veneer ties to backup | | Water management | Mass wall, dries outward | Air space, flashing and weep holes | | Insulation | Interior side | In the backup wall |
Common openings people close
Through-wall AC sleeves
Many Chicago bungalows, two-flats and apartments had through-wall air conditioners cut in under windows or in living rooms. Once central air goes in, the sleeve is a leaky, drafty hole. Brick around them is often cracked from the cut, and the lintel or support over the sleeve may be minimal.
Unused doors
Side, back and basement doors removed during remodels. These are larger, may have a step or stoop outside, and often have a substantial lintel above.
Windows
Windows closed for a kitchen, bathroom or closet layout, or a basement window that keeps leaking.
Coal chutes and old service openings
Small iron doors near the base of older homes that once took coal deliveries. They rust, leak and let in drafts and pests.
Check the rules first
- Permits: closing an opening changes the exterior wall, and many municipalities require a permit. Check with your village or the City of Chicago.
- Egress: sleeping rooms need an egress window under building codes. A bedroom's only window, or a basement bedroom's egress window, generally cannot be bricked up.
- Light and ventilation: some rooms have minimum window or ventilation requirements.
- Historic districts and landmarks: visible exterior changes may need review.
- Neighbors and lot lines: on tight city lots, a wall on the property line may have additional rules.
How a mason bricks up an opening
Every opening differs, but a proper job follows this sequence.
- Remove the unit, frame and sleeve. Take out the window, door, AC unit or chute and its frame, and any caulk or foam.
- Check the lintel. Decide whether the existing steel lintel or arch stays, gets replaced, or comes out with the brick above supported.
- Tooth out the edges. Cut back alternating bricks along each side of the opening so new brick can interlock with the existing courses, rather than leaving a straight vertical seam.
- Prepare the sill area. Remove the old sill if it will not stay, and set a solid base course.
- Build the backup. On solid walls, fill the inner wythes. On veneer walls, frame or block the backup to match the wall around it.
- Lay the face brick. Use matched brick, keeping each course aligned with the courses on either side and toothed into the existing wall.
- Tie it in. Bond across wythes on solid walls, or install veneer ties on veneer walls.
- Keep water out. Install flashing and weep holes at the base of veneer infills and wherever the original wall had them.
- Match the joints. Tool the mortar to the same profile and color as the surrounding wall.
- Finish the inside. Insulate, frame and finish to match the interior wall.
Matching the brick and mortar
The infill is judged on how it looks from the street, so matching is the main event.
| Element | What to match | Tips | |---|---|---| | Brick size | Height, length and thickness | Older brick is often not modern modular size | | Color range | The blend of shades in the wall | Pull several samples; one color rarely works | | Texture | Smooth, wire-cut, sand-struck, rough | Texture changes how color reads | | Weathering | Age and soiling of the wall face | Salvaged brick often blends better on old walls | | Mortar color | Sand and pigment of existing joints | Match to cleaned, weathered mortar | | Joint profile | Concave, raked, flush, struck | Must match or the infill outlines itself |
A useful trick on very visible walls: take brick from a hidden area of the same house, such as a garage wall or the back of a chimney, use it in the visible infill, and replace the hidden spot with new brick.
Materials and techniques
- Brick: matched new brick, salvaged brick of the same era, or brick reclaimed from a hidden area of the house.
- Mortar: Type N for most residential veneer, or a lime-rich mix on older soft brick, matched in color. Mortar should never be harder than the brick.
- Ties: corrosion-resistant veneer ties, or header bonding on solid walls.
- Flashing and weeps: flexible flashing and weep vents at the base of veneer infills.
- Lintels: primed or galvanized steel where a lintel stays or is replaced.
- Insulation: on the interior or in the backup wall.
For more, see Type N vs Type S mortar, salvaged brick sourcing and matching and how brick matching works.
Mistakes we see
- Straight seams: new brick stacked inside the opening without toothing, leaving a crack-prone vertical line on each side.
- Wrong brick size: modern modular brick in an old wall, so the courses do not line up.
- Gray mortar in a tinted or weathered wall.
- Rusted lintel left in place, which keeps expanding and cracks the new brick.
- No flashing on veneer walls, trapping water at the base of the infill.
- Concrete block or plywood behind a single row of face brick, with no ties.
- No insulation, leaving a cold spot inside.
Questions to answer before you close an opening
A little planning keeps the job from turning into two jobs.
Is the opening really unused?
Check for anything still running through it: a dryer vent, a gas line, a cable or electrical run, or a basement window that a furnace room depends on for combustion air. Those have to be rerouted by the right trade before the opening is closed.
What is on the inside?
Decide early whether the interior side will be drywall, plaster or tile, and whether you will hire that work separately. The mason needs to know how far the infill should come to the inside face and where the insulation goes.
Could you want it back?
If there is any chance a future owner will want a door or window there again, say so. The lintel can be left in good condition and the infill laid so it can be removed cleanly later.
Is anything else nearby failing?
Openings often sit next to other problems: a rusted lintel on the window beside it, worn mortar on the same wall, or a cracked sill. Doing them in the same visit saves a second setup and helps the new work blend with the old.
What drives the cost
- Size of the opening: an AC sleeve is a different job from a full door.
- Wall type: solid masonry takes more brick than veneer.
- Brick matching, including salvaged brick.
- Lintel work: keep, replace or remove.
- Height and access.
- Interior finishing, if included.
- Permits and any drawings needed.
Emerald Masonry LLC gives a written, itemized estimate after a free on-site assessment.
DIY vs hiring a pro
Removing an AC unit is a reasonable DIY step. Bricking up the opening is not. Toothing into an existing wall without loosening it, keeping courses level, matching brick and mortar, and handling lintels, flashing and ties take experience, and mistakes show on the outside of your house for good.
Chicagoland context
Chicago-area housing has a lot of closed-off history. Bungalows and two-flats from the 1910s to 1930s often have coal chutes and AC sleeves added mid-century. Post-war ranches and raised ranches have side doors and basement windows that remodels made redundant. And many homes have older infills that were done poorly, now cracking along a straight seam or showing a mismatched patch. Freeze-thaw cycles find any open seam, so a proper infill is as much about keeping water out as appearance. We do this work across Chicago and suburbs such as Oak Lawn, Evergreen Park, Burbank, Palos Heights and Orland Park.
For related house-type guides, see our Chicago two-flat masonry guide and raised ranch and split-level masonry.
Maintenance after the work
- Expect a slight color difference at first; new mortar and brick weather in over a few seasons.
- Keep weep holes clear at the base of veneer infills.
- Watch the seams for the first winter; hairline shrinkage cracks in fresh mortar can be repointed.
- Do not seal or paint the new brick to make it match; it traps moisture.
See why new brick looks different at first.
Related services
- Brick repair for openings, infills and damaged areas.
- Brick replacement for larger sections.
- Lintel repair when the steel above the opening is rusted.
- Tuckpointing to blend joints around the infill.
Conclusion: woven in, tied in, matched
A good infill is solid, dry and hard to find. That comes from toothing the new brick into the old, tying it to the wall, dealing with the lintel and flashing, and matching brick and mortar carefully. Check permits and egress rules first, and the rest is a craftsman's job.
Emerald Masonry LLC is a family-owned masonry contractor serving Chicago and the Chicagoland suburbs, led by career masons with decades of hands-on Chicagoland experience, in brick repair and replacement, tuckpointing and repointing, chimney repair, lintel and limestone sill repair, foundation masonry, caulking, sealing, and residential, commercial and historic masonry restoration. Established 2024; licensed, bonded and insured. Free on-site assessments — call (708) 288-1696.
Want an old opening closed up? Call (708) 288-1696 or book a free on-site assessment.
Frequently Asked Questions
Can you brick up a window in a brick house?
Yes. The window and frame are removed, the opening is filled with brick toothed into the existing courses and tied to the wall, and the inside is insulated and finished. Done well with matched brick and mortar, the infill is hard to spot.
How do you brick in an old through-wall air conditioner sleeve?
The unit and metal sleeve are removed, any damaged brick around the opening is cut back, and the opening is filled with matched brick toothed into the surrounding courses. The lintel or support above is checked, and the inside is insulated and closed up.
Will a bricked-up window always show?
Some difference often shows at first, because new brick and fresh mortar have not weathered. Matching size, color and texture, toothing the brick into the existing courses rather than leaving a straight seam, and matching the mortar make the biggest difference.
Do I need a permit to brick up a window or door?
Often yes, because it changes the exterior wall. Bedrooms also need an egress window under building codes, so a bedroom's only window usually cannot be closed. Check with your village or the City of Chicago before work.
What happens to the lintel above the opening?
It depends on its condition. A sound lintel can usually stay in place, while a rusted one is replaced or removed and the brick above supported. Leaving a badly rusted lintel inside the wall lets it keep expanding and cracking the new brick.
Should a bricked-up opening be insulated?
Yes, on heated spaces. The masonry infill does little to stop heat loss, so the inside is usually framed, insulated and finished like the rest of the wall.
How much does it cost to brick up a window or AC opening?
It depends on the size of the opening, brick matching, the condition of the lintel, height and access, and whether interior work is included. Emerald Masonry LLC gives a written, itemized estimate after a free on-site look.
Who bricks up old openings near Chicago?
Emerald Masonry LLC, a family-owned masonry contractor based in Palos Heights, closes old window, door, AC and coal chute openings on homes across Chicago and the Chicagoland suburbs. Call (708) 288-1696 for a free on-site assessment.